Showing posts with label Woodwork. Show all posts
Showing posts with label Woodwork. Show all posts

Friday, 6 August 2010

Day 3 and lots done

Day three of the recent "spurt" saw lots accomplished.

My plan today was to cut, prep and paint as much as possible early on in the day, so I can get some more of the final thing assembled.  The more this starts to look like the finished job, the more motivation I have to finish it.

The monitor I have is 17" and is that standard "computer monitor grey" colour, so I'm going to need to paint the bezel black so that grey bits aren't showing through the front of the machine.  Try as I might, I can't dismantle it to remove the bezel and paint it, so I've had to carefully mask out the screen and paint the whole thing - only need to do the front as it's the only part to be seen.

Took one of the off-cuts and will build the speaker panel from it.  Offered it up on the top of the monitor panel, marked it out, drew a speaker mesh pattern and drilled it, and also trimmed up another off-cut for the final "roof" of the whole machine.  This is a picture of the monitor and 2 speaker panels with the first coat of MDF primer on the woodwork:



With all these panels painted and dry, I turn my attention to fitting the monitor into the monitor panel.  I'm a fan of the cable-tie-mounts I've used in the past, so will be using these again - search the blog for details of the mounts if interested.

A couple at each corner, eight in total, like this:



Heavy duty cable ties, all trimmed up nicely and it should look something like this:



You'll notice I've put a couple of braces across the back of this section, just to strengthen it.  Pop it back on the control & case sections:



My 80's nostalgia gland is starting to twitch!

Last job of the day is to smash carefully dismantle an old pair of speakers ready for fitting their guts into the speaker panel - I'm using the cheapest set I have, as my memories of sound quality in arcade machines are pretty horrendous, and we do have to try and keep this thing authentic, right??

Thursday, 5 August 2010

The Monitor Section

This morning, the case and the monitor section.

Just to finish off the case section, drilled some "intake" holes for the ventilation near the bottom of the front panel of the case, then a quick coat of MDF primer (I know it's chipboard, but it does a great job of lifting the loose fibres, so a quick sand, then paint, and you do get a really good finish on a really rough piece of wood) and 2 coats of black spray paint, and thus:

On to the monitor.

Another trip to the B&Q and another effort to find a "saw-dodger" (see previous post for the definition of a saw-dodger) and a 6'x2' sheet is cut into 2 x 30"x2' and a 12"x2' off-cut, thus:



Found the centre of one of the big panels by marking corner-to-corner, then accurately measured the visible area on the front of the monitor (the screen of the monitor if you will) and carefully measured and marked it onto the panel, thus:



WARNING - DON'T COPY THE NEXT PART - you'll see why in a bit.

Drilled the four corners to get the jigsaw in, thus:



Turned the jigsaw blade to 45 degrees, to give a better viewing angle on the screen, and a better finish on the panel, and tested with a small cut, thus:



Spot the problem? I want to bevel the sides, but I've drilled straight down.  Bugger.  The four edges will look good, but the corners are just wrong - no other word for it.  If I was dedicated and doing this for someone else, I'd start this panel again, but as I've said earlier, some sacrifices are being made, and I want this finished.  I want to say that this gives the thing character, these little problems, but I'm just in a bit more of a relaxed mood about these things nowadays.  So it looks like this:



I've trimmed the bottom edge at around 15 degrees so that the monitor panel "leans back" into the machine, so that taller users should get a better viewing experience.

TIP FOR THE FUTURE: I haven't leaned it back enough, that, or I haven't built it tall enough because I am having minor viewing issues with the finished box.

2 coats of MDF primer and 2 coats of black spray paint.

Propped the monitor panel on the top of the case and control panel and this is what I've got:



Is it just me, or is this starting to look like an arcade machine??? :-)

Sides for the monitor panel next.  Using one of the off-cuts, offered up the piece to the side of the monitor and marked out the size and shape of the sides for the monitor.  Cut them, and offered them up to check the fit:



Lay the monitor panel on the floor and glued and screwed to put it together:



That'll do for today - pick it up again in the morning when it's time to get the screen in, I reckon.

Tuesday, 3 August 2010

Building the case

On the 3rd August, I popped over to the B&Q, fetched a big sheet (8'x4') of 18mm Chipboard off the shelf, and set about finding someone to run the big saw to chop it into manageable pieces for me.  This proved harder than I expected, as it seems running the saw is a job to be dodged at my local B&Q.

Finally found someone, and got them to turn one sheet into this:



The idea is to make a 30" high by 30" wide case, so I got the man to cut it 3x30" parts, then cut the 30" by 4' down to 30" by 30".

So I ended up with 3 x 30" x 30" panels, 3 x 30" x 18" panels, and a 6" by 4' panel.

I want the finished case to have a single panel on the front, so when it's put together, I see only one panel from the front, without side or top "bits" so I split one of the 30's into 2 x 15"x30" for my sides, thus:



I did draw for some cut-outs on the side panels to give a more "arcade machine feel" to the design, but quickly realised that not only would it be harder to construct a front to fit the cut-outs, but the PC would have very little room inside the case.

DESIGN NOTES: It's worth pointing out at this point that I've decided to sacrifice a few aspects of the design.  It's important to me to get this finished now, so I will be cutting the odd corner here and there, but I still want something relatively authentic (nice?) to look at, so will try not to sacrifice too much.  I'm not going to have an access panel in the case section as per earlier designs - I'm going to screw the panel to the case unit, and unscrew when I need to fix/upgrade something.  Hopefully this will be rare.  Anything to do with software/files on the machine I can do remotely over the network.  Ubuntu/Linux gives me enormous flexibility and control that Windows simply doesn't provide

Trim 2 of the 18"x30" off-cuts down to 15" (minus the thickness of 2 sides = 36mm) and I now have two sides, a top, a bottom, a back and a front.

Put all but the back together and we get this:



And with the front:



Under the control panel - open and closed:



You might see a little ledge at the back? I could claim it's deliberate but it's not.  I'd not taken into account how much room the control panel needed when opened, so it doesn't meet the back - that's not as important as you might think as I'll be fixing sides onto this beast that will hide these "redesign factors" but also, it gives me the opportunity to drill some holes in that little ledge for ventilation of the case compartment - more on this next

Thursday, 18 March 2010

I love the smell of spray paint in the morning

So, another visit to my dentist, and my tooth is fixed.

I have some MDF sealer and primer that I've used in the past on Chipboard and it works quite well - I like that it goes on a bit of a purple colour, then dries clear:

[caption id="attachment_207" align="aligncenter" width="300" caption="sealer and primer"]sealer and primer[/caption]

Two coats of primer, with a quick sanding with 800 grit paper in between to get a very smooth finish, then one coat of black spray paint and you get this - looking tasty! :

[caption id="attachment_208" align="aligncenter" width="225" caption="control: 1 coat"]control: 1 coat[/caption]

A second coat of black spray, and the buttons installed:

[caption id="attachment_209" align="aligncenter" width="300" caption="control: all painted"]control: all painted[/caption]

That'll do for today! Tomorrow - the wiring!!!

Tuesday, 16 March 2010

Can I finish the control panel today?

I'm writing this at the end of the day, and I feel like it's been very productive.

After the dentist (no work to be done there, thankfully) I'm putting together all the pieces cut yesterday.

I've used some long braces to strengthen the base, as it's put together from two pieces - not pretty, but as they say, out of sight...

[caption id="attachment_174" align="aligncenter" width="300" caption="a bit of a fudge?"]a bit of a fudge?[/caption]

Marked out for, and fitted the piano (continuous) hinge to the main carcass:

[caption id="attachment_175" align="aligncenter" width="225" caption="piano hinge - 1"]piano hinge - 1[/caption]

Propped up the main carcass, to get that part to the right height to connect the other half of the hinge to the correct place on the tilt & front section:

[caption id="attachment_176" align="aligncenter" width="225" caption="piano hinge -2 "]piano hinge -2 [/caption]

Then offered up the tilt & front and connected the other half of the piano hinge:

[caption id="attachment_177" align="aligncenter" width="225" caption="piano hinge - 3"]piano hinge - 3[/caption]

So it looks like this when it's closed:

[caption id="attachment_178" align="aligncenter" width="225" caption="closed - 1"]closed - 1[/caption]

Notice the gap? Yeah, not particularly happy about that - I was hoping it would close flush, but with a bit of jiggling, glueing, etc. it gets better, but not great.

STOP THE PRESS - just at that point (literally!) the postman arrived with my buttons and sticks. Yey! - as you can see, a fantastic picture (not!):

[caption id="attachment_163" align="aligncenter" width="300" caption="box of bits"]box of bits[/caption]

So, time to mark up the control panel section for the sticks and buttons (no real design for this, just "guessed" by putting my hands on the box in the places where they naturally rested when thinking about using sticks and buttons):

[caption id="attachment_179" align="aligncenter" width="225" caption="buttons design"]buttons design[/caption]

I have a bench drill, and some nice bore drill bits:

[caption id="attachment_180" align="aligncenter" width="225" caption="pride and joy"]pride and joy[/caption]

Drill one hole, and inserted a button to test - nice! :

[caption id="attachment_181" align="aligncenter" width="225" caption="first button"]first button[/caption]

So, plenty of dust and shredded chipboard later and it looks like this:

[caption id="attachment_182" align="aligncenter" width="225" caption="all holes cut"]all holes cut[/caption]

I'm going to put the "coin" and "1UP / 2UP" buttons on the front panel - I think it's more nostalgic like this:

[caption id="attachment_183" align="aligncenter" width="225" caption="1UP holes"]1UP holes[/caption]

And with the final woodwork construction done, it looks like this when open:

[caption id="attachment_186" align="aligncenter" width="225" caption="end of tuesday - open"]end of tuesday - open[/caption]

And this when closed:

[caption id="attachment_184" align="aligncenter" width="225" caption="nice"]nice[/caption]

I'm still not happy about that gap, so I'm going to get some decorative thumb-turns to hold the tilt closed:

[caption id="attachment_185" align="aligncenter" width="225" caption="thumbturn"]thumbturn[/caption]

Not ideal, but you have to be a bit "organic" when doing something like this, as the cabinet evolves into something similar to what you designed, but it'll never be exactly what you expected - well not for me, anyway.

I've done some glueing, and used some wood filter to fill the unsightly edges in, gave all the visible surfaces a good sanding.  It's not looking too bad at all.

Next stage will be to prep and paint the visible surfaces, then install the buttons and sticks, then do some wiring.  I'm making better progress with this than I expected.

Something's bound to go wrong.

Cost so far = £80.36
IPAC VE – £30
ROMS – £5
Buttons and Joysticks – £20.01
Piano Hinges – £4.38
Corner Brackets – £1.90
Chipboard - £13
Thumbturns - £5.98

The first few bits of wood

So I found myself with a free afternoon on Monday, popped to the B&Q on the way home from work, and had a wander around the wood panels section - funny how much I enjoy these activities, but would mock others if they mentioned it.

MDF is 3 x the price of Chipboard.  Yes, I know, MDF has a smooth finished surface that lends itself quite nicely to arcade machines, but with a little love, effort and attention, Chipboard brushes up OK.  So chipboard I bought.

Started off by slicing it all down to 30", the width of my finished machine.

The hardest part about cutting the wood will be getting the angles right to achieve the "tilt" on the control panel.  I set the jigsaw bed to a 20 degree (ish?) tilt and this is the result:

[caption id="attachment_153" align="aligncenter" width="300" caption="angles - end view"]angles - end view[/caption]

I took some of the 90 degree brackets, put them in the vice, and squeezed them until they matched the angle of the wood:

[caption id="attachment_149" align="aligncenter" width="300" caption="angle brackets - bent"]angle brackets - bent[/caption]

I offered them up to the angled piece to test the angle of the bracket:




[caption id="attachment_150" align="aligncenter" width="300" caption="offered up to check"]offered up to check[/caption]

and attached the front to the tilt, like so:





[caption id="attachment_154" align="aligncenter" width="300" caption="front + tilt"]front + tilt[/caption]

The rest of the control panel carcass was quite straight forward, cut to the design I sketched yesterday.  I used lots of the angle brackets to fix all the parts together:





[caption id="attachment_156" align="aligncenter" width="300" caption="main control panel - brackets"]main control panel - brackets[/caption]

You've probably noticed the line along the base - I ran out of wood! I've cobbled together a base from two off-cuts - seems overkill to make this "fresh" as it won't be seen in the finished cabinet.


I've offered all the pieces up together to see what it's gonna look like - i think it's quite true to my sketch??





[caption id="attachment_188" align="aligncenter" width="225" caption="first mockup"]first mockup[/caption]

I've taken tomorrow off work, so I should be able to make some progress, even though there's a dentist appointment in the middle of my morning.

Sunday, 14 March 2010

Sunday

Sunday afternoon has been productive, but not as much as I'd hoped.

Here's another sketch of the control panel section.



[caption id="attachment_142" align="aligncenter" width="300" caption="control panel sketch"]control panel sketch[/caption]

I've been back to B&Q today to look at their MDF - I think I used 12mm last time, and had an issue when it came to mounting the joysticks. I remember that the screws that mounted the joystick underneath the panel started to come through the top surface ever so slightly.

So I'm going to go with the 18mm - more expensive, and the final product will be significantly heavier, but I think it's the tight thing to do. I've recalculated the sizes based on 18mm and I think I've got it right. Apologies for mixing imperials and metrics, but it's how I work.

I have sourced the piano hinges for the control panel and the main computer section today - £2.19 each from Wickes is an absolute bargain.

Also, I've picked up a pack of 50 corner brackets for £1.99 from Screwfix to connect the MDF panels together.

[caption id="attachment_147" align="aligncenter" width="300" caption="angle brackets"]angle brackets[/caption]

Last time, I used 1" sq. strips of wood along each face, which contributed to the lack of space inside the case for the controls - plus it was a lot more cutting and drilling, etc. These little brackets should save a lot of time and effort connecting panels.

Tomorrow I hope to pick up some MDF and if I've got time, cut the panels for the control section.

Cost so far = £61.38
IPAC VE - £30
ROMS - £5
Buttons and Joysticks - £20.01
Piano Hinges - £4.38
Corner Brackets - £1.9

Thursday, 7 February 2008

Illuminate.

I'm getting quite quick at this.

Today I only had an hour spare and I entirely built (not painted) the "above marquee" panel, from an odd shape piece of 9mm MDF that I had left over.  This had sat underneath the panels I had painted, so is a bit messy on one side as you'll see in the pictures.

With only 1 face that was cut at the factory, I ran the piece through the table saw 3 times to get 4 square sides, then trimmed to 2' (60cm)  width.  Using the router, I rounded over the outer face, front edge (as per the under marquee panel) offered it up to the cab, marked it for length, and cut to length.

At this point, time to install the last of the electronics (bar the PC) the marquee light.  I have an old 20" (~50cm) strip light in my spares box in the garage, so I've decided the best way to install this is on the reverse side of this above marquee panel (this has the most available space and close enough to the top panel.)  I've used some 1/4" (~6mm) thick hard rubber strip to separate the housing of the strip light from the wood (I'm thinking heat insulation but I could be mad) PVA'ed into place, and screwed the strip light, through the rubber into the MDF.  The rubber layer adds some additional thickness so that the 1/2" (12mm) screws don't burst through the other side of the 9mm MDF.  At this stage, I've also wired the light with a standard plug on the other end.  I meant to put a switch part way through the length of the cable, but I forgot.  I can always revisit this if I decide I want to have the option of lights on or off.

The following photograph shows the underside of the finished (bar painting) above marquee panel.

Top Panel

and with it installed

From above

Lights!

Light Bleeding

OK - I suspected this might be a problem, as I'd read similar marquee issues on other cab building sites.

The light is bleeding through the black sections of my artwork terribly - washing them out in a hazy grey colour.  Not good.  Solutions I have read about include printing the artwork twice then cutting out the non-black parts to leave a black template to stick under the finished logo, in essence making the black sections twice as thick.  I don't really have that option without begging my brother for another print run (and my favour account is in the red) so at some later point, I'll whip out the marquee, and paint black on the non-visible side to control the light bleed.  As there's no back yet constructed, you can see the light pouring out the back - I'll have to think about some form of reflector pushing all the light forward if too much bleeds out of the cracks.  That's an unknown until we're nearly complete.

My enthusiasm is re-stoked, but I'm now out of MDF.  I'll need a trip to my timber yard again before I can carry on.  Hopefully the weekend if not before.

Here's the cabinet as at now!

Latest

Next panel in the plan - the angled vent panel!

Tuesday, 5 February 2008

Get up, you lazy monkey!

To start the day off, a quick trip to Screwfix to pickup some magnetic catches.

Magnetic Catches

I've had a "light-bulb moment" over the easy access to controls by making the vent panel held in place by the kinds of magnetic catches that hold AV unit doors closed. a few of these in the right place, and the panel will hold firm, but will simply lift off with a bit of leverage to allow for quick easy access to the inside top controls - more on this in the post where I build that panel.

After an unproductive weekend (where the cab is concerned) I picked myself up and put a couple of hours in this morning - I built the panel that sits underneath the marquee between marquee and speaker panel. This took longer than anticipated for a couple of reasons. My table saw didn't come with a bench to raise it to a workable level, so I built one. Unfortunately, I accidentally built my bench with a support brace across the front, thus rendering the "tilt" mechanism (setting an angle on the cutting blade) unusable. So this morning's first task was to modify the table saw to reactivate the angle facility.

Once I'd fixed the saw, I tilted the blade to 45 degrees, cut one side of a panel at 45 to meet the 45 tilt on the speaker panel, then offered up to the cabinet, and marked the length. Back to the saw, swing the blade back up to 90 degrees and cut the panel to length. I used the router to round over the lower edge under the marquee so that, when finished, all four sides of the marquee will have their outer edges rounded - a nice effect I think.

Under Panel Profile

Currently it's held in place with some clamps:

Under Panel from UnderneathI need to be careful now as most of the remaining panels will need to be painted all together - I'm wasting far too many paint accessories painting one panel at a time. So for now, it'll stay with the clamps and for the next stage, I'll move onto the "above the marquee" panel.